Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL GTX™ Resin GTX6009 - Americas - (PPE+PA*) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL GTX™ Resin GTX6009 - Americas:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Noryl GTX datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses - Recommandations pour la transformation Moulage par injection
Any use of this information falls under the rules of our disclaimer.
Informations produit
NORYL GTX™ 6009 resin is a non-reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). This injection moldable grade exhibits high heat resistance, and excellent chemical resistance. NORYL GTX6009 resin may be an excellent candidate for exterior automotive applications such as wheel covers and wheel trim.
Propriétés mécaniquesValeurUnitéNorme du test
ASTM Data
Module de traction d’élasticité 53 MPa ASTM D 638
Allongement à la rupture 90 % ASTM D 638
Module de flexion 2130 MPa ASTM D 790
Dureté Rockwell R 110 - ASTM D 785
Izod choc avec entaille, 1/8 in 736 J/m ASTM D 256
Propriétés thermiquesValeurUnitéNorme du test
ASTM Data
DTUL à 66 psi 160 °C ASTM D 648
Propriétés électriquesValeurUnitéNorme du test
ASTM Data
Résistance volumique >1E15 Ohm*cm ASTM D 257
Propriétés diversesValeurUnitéNorme du test
Densité 1120 kg/m³ ASTM D 792
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 95 - 105 °C -
Pré-séchage - temps 3 - 4 h -
L'humidité de traitement ≤0.07 % -
Température de la matière fondue 280 - 305 °C -
Température du moule 75 - 120 °C -
Zone 1 265 - 305 °C -
Zone 2 270 - 305 °C -
Zone 3 275 - 305 °C -
Vitesse de rotation de vis 20 - 100 rpm -
Contre-pression 0.3 - 1.4 MPa -
Caractéristiques
Transformation
Moulage par injection
Applications
Automobile
Disponibilité régionale
Amérique du nord
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.